North America / English  Change

 

Shark® Series
7008, 7009, 7010 Grinder Pumps

1.0, 1.5 & 2.0 HP, single direction grinder pumps. Uniquely designed for residential or commercial use

 
 
Features andBenefits
EngineeringFeatures
TechnicalData
Literature and Documents

APPLICATIONS

  • Sanitary sewage
  • Housing developments
  • Pressure sewers

SPECIFICATIONS

PUMP:

  • Nonautomatic or automatic with integral on-off switch
  • cCSAus listed
  • Discharge: 1-1/4” NPT vertical
  • Mechanical seal – silicon carbide/carbon with Buna-N elastomers
  • Construction – cast iron ASTM A-48, Class 30, 30,000# tensile strength
  • Attaching hardware and lifting handle – 304 stainless steel
  • Square ring seals - Viton
  • Impeller – engineered, glass-filled plastic with stainless steel insert and top pump-out vanes
  • Corrosion-resistant, epoxy coated finish
  • 440C stainless steel Tri-slice® cutter and plate hardened to Rockwell C55-60
  • Optional:
    • Extended cord length
    • Silicon carbide/silicon carbide seal
    • Bronze impeller
    • Trimmed impeller (bronze only)
    • Pre-packaged systems
    • Rail systems

 MOTOR:

  • Capacitor start/run motor with integral starting circuit
  • 1 Phase – integral thermal overload
  • Stainless steel motor shaft
  • Stator – Class B insulation and lead wires, Nema B design
  • Housing – Cast iron, oil-filled, protected by cooling fins
  • Upper and Lower Ball Bearings – Dual high carbon chromium steel
  • Power cable length – 20’ (6 m) standard

DIMENSIONS:

  • Height: 18-5/8” (47.3 cm)
  • Major Width: 11-5/8” (29.5 cm)
  • Weight: 88 lbs (40 Kg)
Note: Product information presented here reflects conditions at time of publication. Consult factory regarding discrepancies or inconsistencies.

Easy installation – Pump is supplied with 20' (6 m) of multi-conductor power cable as standard, in either an automatic unit furnished with integral on/off control or nonautomatic type. Alternate cable lengths are available. Units have 3 legs as an integral part of pump housing for free-standing requirements. Pump and motor assembly can be easily lowered into position without disturbing the piping by use of a rail system. Pump is furnished with a stainless steel lifting handle.

 

Long-lasting, internal components – Class B insulation system rated for 130° F (54° C) max liquids. Thermal protection standard on all motors. Conservatively rated antifriction ball bearings for thrust loads. Finned, oil-filled motor housing, for greater heat dissipation, and cooler running motors. Cutter and plate can be re-sharpened to extend pump life. Both are made of high-quality, 440C stainless steel and hardened to a value of 55-60 on a Rockwell C scale. Capacitor start/capacitor run motor provides extra start and run torque for cutting.

 

Complete environmental protection – Viton square rings and heavy duty cord connectors keep liquid from entering the motor assembly. Motor housing is constructed of finned powder coated epoxy coated Class 30 cast iron. Hardware is stainless steel. Seal faces are silicon carbide/carbon for corrosion resistance and provide complete protection for motor internals. Seal has stainless steel and Buna-N components. Vent hole helps prevent air locking. Engineered plastic vortex impeller with top pump-out vanes for seal protection is keyed and bolted to the shaft. The pump housing has a concentric design thereby equalizing the pressure forces inside the housing, which will extend the service life of the seal and bearings. All pumps come with 1¼” NPT female vertical discharge.

  • 54
  • 2
  • 8
  • 12

 

×

 

×